Which two security features can be configured to prevent unauthorized access into the network through a networking device? (Choose two.)

What command would be used to verify trusted DHCP ports?

 Which QoS Profile is selected in the GUI when configuring a voice over WLAN deployment?

Which two statements about NTP operations are true? (Choose two.)

Refer to the exhibit. Which feature is enabled by this configuration?

Which NAT term is defined as a group of addresses available for NAT use?

Which statement about the nature of NAT overload is true?

Refer to the exhibit. An engineer configured NAT translations and has verified that the configuration is correct. Which IP address is the source IP?

Which keyword in a NAT configuration enables the use of one outside IP address for multiple inside hosts?

Which type of address is the public IP address of a NAT device?

Refer to the exhibit. Router R1 is configured with static NAT. Addressing on the router and the web server are correctly configured, but there is no connectivity between the web server and users on the Internet. What is a possible reason for this lack of connectivity?

An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any of three addresses 192.168.3.1, 192.168.3.2, 192.168.3.3. Which configuration should be used?

Which command should you enter to configure a device as an NTP server?

Which two pieces of information can you determine from the output of the show ntp status command? (Choose two)

Which two pieces of information can you determine from the output of the show ntp status command? (Choose two)

Which two tasks must be performed to configure NTP to a trusted server in client mode on a single network device? (Choose two)

What will happen if you configure the logging trap debug command on a router?

If a notice-level messaging is sent to a syslog server, which event has occurred?

What event has occurred if a router sends a notice level message to a syslog server?

Which command must you enter to guarantee that an HSRP router with higher priority becomes the HSRP primary router after it is reloaded?

Which command should you enter to verify the priority of a router in an HSRP group?

Which MAC address is recognized as a VRRP virtual address?

Which two outcomes are predictable behaviors for HSRP? (Choose two)

How does HSRP provide first hop redundancy?

What is the primary purpose of a First Hop Redundancy Protocol?

When the active router in an HSRP group fails, what router assumes the role and forwards packets?

What are two roles of Domain Name Services (DNS)? (Choose two)

Which command must be present in a Cisco Device configuration to enable the device to resolve an FQDN?

What facilitates a Telnet connection between devices by entering the device name?

How does a router behave when configured with the default DNS lookup settings, and a URL is entered on the CLI?

What are two roles of Domain Name Services (DNS)? (Choose two.)

A network administrator enters the following command on a router: logging trap 3. What are three message types that will be sent to the Syslog server? (Choose three.)

Which Cisco IOS command will indicate that interface GigabitEthernet 0/0 is configured via DHCP?

Which command enables a router to become a DHCP client?

What are two roles of the Dynamic Host Configuration Protocol (DHCP)? (Choose two)

Refer to the exhibit. An engineer deploys a topology in which R1 obtains its IP configuration from DHCP. If the switch and DHCP server configurations are complete and correct. Which two sets of commands must be configured on R1 and R2 to complete the task? (Choose two)

Refer to the exhibit. If the network environment is operating normally, which type of device must be connected to interface FastEthernet 0/1?
ip arp inspection vlan 2-10
interface fastethernet 0/1
ip arp inspection trust

Which type of information resides on a DHCP server?

What is a DHCP client?

Where does the configuration reside when a helper address is configured to support DHCP?

When implementing a router as a DHCP server, which two features must be configured? (Choose two)

Which command must you enter to configure a DHCP relay?

Where does a switch maintain DHCP snooping information?

A network engineer must back up 20 network router configurations globally within a customer environment. Which protocol allows the engineer to perform this function using the Cisco IOS MIB?

Which function does an SNMP agent perform?

Which command must be entered when a device is configured as an NTP server?

 What event has occurred if a router sends a notice level message to a syslog server?

Refer to the exhibit. An engineer configured NAT translations and has verified that the configuration is correct. Which IP address is the source IP after the NAT has taken place?

An engineer is configuring NAT to translate the source subnet of 10.10.0.0/24 to any one of three addresses: 192.168.3.1, 192.168.3.2, or 192.168.3.3. Which configuration should be used?

Drag and drop the SNMP components from the left onto the descriptions on the right.
Select and Place:

What is a function of TFTP in network operations?

What is a DHCP client?

Where does the configuration reside when a helper address is configured lo support DHCP?

When deploying syslog, which severity level logs informational messages?

Refer to the exhibit. An engineer is configuring the router to provide static NAT for the webserver. Drag and drop the configuration commands from the left onto the letters that correspond to its position in the configuration on the fight.
Select and Place:

Which feature or protocol determines whether the QoS on the network is sufficient to support IP services?

Which two actions are performed by the Weighted Random Early Detection mechanism? (Choose two)

Which two QoS tools can provide congestion management? (Choose two)

Which option is the main function of congestion management?

What does traffic shaping do to reduce congestion in a network?

Which feature can you implement to reserve bandwidth for VoIP calls across the call path?

What is the purpose of traffic shaping?

Which function does an SNMP agent perform?

Order the DHCP message types as they would occur between a DHCP client and a DHCP server.

Drag and drop the QoS congestion management terms from the left onto the description on the right.

Drag and drop the DHCP snooping terms from the left onto the descriptions on the right.